25 Degree Frame (1937 - 1940) 28 Degree Frame (1941 - mid 1946) 30 Degree Bullneck (mid 1946 - mid 1947) Wishbone Frames (1948 - late 1954) Straight Leg Frame (late 1954 - 1957)

Bullneck frame was added to the line mid 1946 and ran until mid 1947.


To purchase any of these items or to enquire about availability please send an email to raceframe@gmail.com .




TRANS BRACE STIFFENER (RFE Part Number VC36 1936-1939 ONLY)

Trans Brace Stiffener

These are sold in sets of two and come loose for ease of fitment.
Depending on the year of your frame they will need either - " tacking and brazing" , or "electric welding" in place.
They have the stiffening indent pressed into them as per original and come fully pressed for seat post and rear trans lug.

Price per set is $118.00 per set + tax if applicable. Overseas orders are exempt from Tax

Trans Brace Stiffner Trans Brace Stiffner

OIL TANK MOUNT (RFE Part Number VC10)

Oil Tank Mount

Oil Tank Mount is fully machined and ready to fit.

Price is $49.00USD each + tax if applicable. Overseas orders are exempt from Tax

RIGID RUNNING BOARD LUGS (RFE Part Number VC11)

Running Board Lugs

Rigid Running Board Lugs are sold each and are fully machined and ready to fit.

Price is $36.00 each + tax if applicable. Overseas orders are exempt from Tax

REAR INNER PRIMARY MOUNT (RFE Part Number VC14)

Rear Inner Primary Mount

Fits 1936 through 1957 bikes.

Price is $20.00 each + tax if applicable. Overseas orders are exempt from Tax

FRONT ENGINE MOUNT (RFE Part Number VC64)

Front Engine Mount

Front engine mount to suit 1937 through to the end of the 1947 production run. Suitable for all Knuckle and Flathead frames to 1947 only.

Price is $389.00 each + tax if applicable. Overseas orders are exempt from Tax

BRAKE CROSS OVER STIFFNER (RFE Part Number VC65)

Brake Cross Over Stiffner

Brake Cross Over Stiffner is fully machined and ready to fit.

Price is $49.00 per set + tax if applicable. Overseas orders are exempt from Tax

Brake Cross Over Stiffner

EL TOP ENGINE MOUNT (Brazed) (RFE Part Number VC15-B)

Top Engine Mount Right view

This part is tacked to the frame and then brazed. This is the original proceedure for 1936-37 only. You will note that the tank mounts are brazed in position. This is correct for 36-37 only. The slotted hole is 11/16 long. This is correct for 1936 to mid 1940.
See VC15 for 1938-40 top engine mount.

Price is $118.00 per set + tax if applicable. Overseas orders are exempt from Tax

Top engine Mount Left view Top engine Mount view from Above

EL TOP ENGINE MOUNT (RFE Part Number VC15)

Top Engine Mount Right view

This part is suitable for 1936 to late in the 1940 production run.
This is the top engine mount for the early EL's. The seat T pivot hole is tapped to 5/16UN. The slotted hole is just over 11/16" ("45/64" as was used by OEM). It is assembled with 2 tack welds in the same places as the originals had during this period.
Please Note : Late in the 1940 production run the slotted hole was increased to 55/64 to accomodate the new 1200cc cylinders. If you have a late 1940 FL engine this top engine mount VC15 is NOT for you. Go to RFE part VC26 for FL top engine mount.

Price is $95.00 per set + tax if applicable. Overseas orders are exempt from Tax

Top Engine Mount Left view

FL TOP ENGINE MOUNT (RFE Part Number VC26)

Top Engine Mount

Top Engine Mount is fully fabricated and ready to fit.

Price is $95.00 per set + tax if applicable. Overseas orders are exempt from Tax

KNUCKLEHEAD/FLATHEAD/PANHEAD REAR TRANS POST (RFE Part Number VC28)

Rear Trans Post

Rear Trans Post is straight knurled and ready to fit. It is knurled like OEM and comes with matching spacer. The spacer is placed between the trans cross brace plates
These are sold as a unit.

Price is $42.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGID BRAKE CROSSOVER TUBE (RFE Part Number VC33)

 

Brake Crossover Tube is knurled and machined ready to accept bush.

Price is $45.00 each + tax if applicable. Overseas orders are exempt from Tax

INTERMEDIATE BACKBONE (RFE Part Number VC35)

Intermediate Backbone Full picture

This part is straight knurled one end to allow the Braze to flow. The other end is contour pressed to mate to the 1 1/2" Backbone.
A 3/32" hole is drilled into this part to allow the gas and hot air to escape while brazing is taking place.
An exact reproduction of the intermediate backbone used from 1938 through to the end of the run of rigid frames in 1957.

Price is $59.00 each + tax if applicable. Overseas orders are exempt from Tax

Intermediate Backbone Contour Pressed End Intermediate Backbone Knurled End

SEAT POST CLUSTER (RFE Part Number XE-1)

 

Seat Post Cluster is fully machined ready to fit.

Price is $288.00 each + tax if applicable. Overseas orders are exempt from Tax

STRAIGHT LEG DOWN TUBE (RFE Part Number VC37)

 

Straight Leg Down Tube is knurled both ends and ready to fit.

Price is $32.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGID FENDER RAILS (RFE Part Number VC40)

 

Fender Rails are knurled and pressed as per original and sold left or right side.

Price is $86.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGID FENDER RAIL BRACE (RFE Part Number VC41)

 

 

Price is $29.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGID BOTTOM RAIL LEFT SIDE (RFE Part Number VC42)

 

Left Bottom Rail is knurled both ends and has chain relief as per original.

Price is $118.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGID BOTTOM RAIL RIGHT SIDE (RFE Part Number VC43)

 

Right Bottom Rail is knurled both ends and is formed as per original.

Price is $98.00 each + tax if applicable. Overseas orders are exempt from Tax

BACKBONE (RFE Part Number VC46, VC70)

Backbone

Backbone is supplied with straight knurling on the neck end. An internal stiffner tube is sweat brazed into the seat post cluster end and a relief is pressed to the under side to clear the inlet tin on FL's. All are exact duplicates of the original item produced by the factory from late 1940 to 1947.

Price is $98.00 each + tax if applicable. Overseas orders are exempt from Tax

Backbone Knurled End Backbone Centre Backbone End View

LOWER SEAT POST BRACE (RFE Part Number VC47)

 

Lower Seat Post Brace is pressed to original shape and drilled to accept bash plate and seat post base.

Price is $39.00 each + tax if applicable. Overseas orders are exempt from Tax

UPPER SEAT POST BRACE (RFE Part Number VC48)

 

Upper Seat Post Brace is pressed to original shape and drilled to accept seat post.

Price is $39.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGID REAR TRANS CROSS BRACE (RFE Part Number VC52)

Rigid Rear Trans Cross Brace Down

Rear Trans Cross Brace is pressed to original shape and drilled to accept rear trans posts.

Price is $34.00 each + tax if applicable. Overseas orders are exempt from Tax

Rigid Rear Trans Cross Brace Up

TRANSMISSION OUTRIGGER SUPPORT (RFE Part Number VC60)

Transmission Outrigger Support 1

Pressed to original shape. This bracket will fit snuggly around tube to give a nice tight fit for brazing or electric welding, depending on the correct welding procedure for the year of your frame. Shim plate is spot welded to bracket as was OEM.

Price is $49.00 each + tax if applicable. Overseas orders are exempt from Tax

Transmission Outrigger Support 2

LOWER FENDER SUPPORT (RFE Part Number VC62)

Lower Fender Support Below

Rear Lower Fender Support is pressed to original shape and ready to fit.

Price is $49.00 each + tax if applicable. Overseas orders are exempt from Tax

Lower Fender Support Top Lower Fender Support Side

REAR ENGINE MOUNT (RFE Part Number VC66)

Rear Engine Mount

Fully machined and ready to fit. Please note that this item is for Knucklehead and Flatheads frames 1936 through 1947 only.
You will note that the script and foundry mark are large "5/16 inch".
The Panheads had a smaller ''3/16 inch'' script. For Panhead rear engine mounts go to the Wishbone or Straight leg page on this site.

Price is $349.00 each + tax if applicable. Overseas orders are exempt from Tax

LOWER TANK MOUNT (RFE Part Number VC96)

Lower Tank Mount

Lower Tank Mount is pressed to original shape and ready to fit.

Price is $48.00 each + tax if applicable. Overseas orders are exempt from Tax

1936-1937 TOOLBOX BRACKET (RFE Part Number VC82)

33-37 Toolbox Bracket top

This is a faithful reproduction of the original toolbox bracket with the spot welded rectangular pads.
These brackets have the correct contours and pressed reliefs. When the ends of the bracket are tapped around the frame during fittment they wrap around like OEM to the same place and look correct. They are exactly 2" wide as was OEM. The Taiwan brackets are 2 1/4" wide and are easily picked with poorly pressed reliefs and edges. The spot welded rectangular pads are taped 5/16" unf.
If this bracket is fitted to your frame correctly, and welded in the correct fashion, it will pass judging without comment or point loss.

Price is $118.00 each + tax if applicable. Overseas orders are exempt from Tax

33-37 Toolbox Bracket Below

1938-1939 TOOLBOX BRACKET (RFE Part Number VC82)

38-39 Toolbox Bracket top

This is a faithful reproduction of the original toolbox bracket with the spot welded round washers.
These brackets have the correct contours and pressed reliefs. When the ends of the bracket are tapped around the frame during fittment they wrap around like OEM to the same place and look correct. They are exactly 2" wide as was OEM. The Taiwan brackets are 2 1/4" wide and are easily picked with poorly pressed reliefs and edges. The spot welded round pads are taped 5/16" unf.
If this bracket is fitted to your frame correctly, and welded in the correct fashion, it will pass judging without comment or point loss.

Price is $118.00 each + tax if applicable. Overseas orders are exempt from Tax

38-39 Toolbox Bracket Below

SLEEVING JOINT (RFE Part Number VC100)

Sleeving Joint

Steel Sleeving joint for all Knuckle and UL frames. This part is brazed to the ends of the upper rear fender brace.

Price is $26.00 each + tax if applicable. Overseas orders are exempt from Tax

TOOLBOX BRACKET (RFE Part Number VC102)

Toolbox Bracket Top View

This is a faithful reproduction of the original 1940 toolbox bracket with the riveted cross bar. Some of the very first 1941 had these as well.
These brackets have the correct contours and pressed reliefs. When the ends of the bracket are tapped around the frame during fittment they wrap around like OEM to the same place and look correct. They are exactly 2" wide as was OEM. The Taiwan brackets are 2 1/4" wide and are easily picked with poorly pressed reliefs and edges. The crossbar has the spot welded pad which is taped 5/16" unf.
If this bracket is fitted to your frame correctly, and welded in the correct fashion, it will pass judging without comment or point loss.

Price is $118.00 each + tax if applicable. Overseas orders are exempt from Tax

Toolbox Bracket Top View Closeup

STRAIGHTLEG SIDECAR LUGS (RFE Part Number VC105L (Left), VC105R (Right) )

Straightleg Sidecar Lugs 1

These are made of Steel and will suit 1937 through 1947 and late 1954 through 1957 frames. The part numbers and Hallmarks are clear and have a clear flash mark running down the front and rear of the part exactly as did Original parts.

Price is $259.00 per side + tax if applicable. Overseas orders are exempt from Tax

Straightleg Sidecar Lugs 2 Straightleg Sidecar Lugs 3 Straightleg Sidecar Lugs 4

LEFT AXLE CARRIER (RFE Part Number VC108L)

Left Axle Carrier

Exact reproduction of Left axle carrier from 1938 - 1957. Comes fully machined and ready to fit. Faithful reproduction of the part number and Hallmark.

Price is $319.00 each + tax if applicable. Overseas orders are exempt from Tax

RIGHT AXLE CARRIER (RFE Part Number VC108R)

Right Axle Carrier

Exact reproduction of 1938 - 1957 right axle carrier. Machined to exact OEM tolerances. Faithful reproduction of the part number and Hallmark. This part comes fully machined and ready to fit. Can be supplied with plug weld holes if desired.

Price is $319.00 each + tax if applicable. Overseas orders are exempt from Tax

Right Axle Carrier side view



To purchase any of these items or to enquire about availability please send an email to raceframe@gmail.com .